Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
TraneSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateFast, Reliable Furnace Repair Across Farmers Branch
Furnace repair in Farmers Branch typically runs $150 – $700, and because our crews already work in Farmers Branch every week, we can usually have a technician at your door the same day you call. Cold Harbour Heating and Air Dallas brings a written price before any work starts, a firm arrival window, and a 365-day guarantee on every repair. That’s the short version. The longer version is that we know exactly what the older ranch homes and newer infill builds in this city throw at a heating system, because we’ve been inside hundreds of them.
Call (430) 213-5796 if your furnace is acting up. A real person answers, day or night.
Why Cold Harbour Heating and Air Dallas Is Farmers Branch’s Preferred Furnace Repair Company
Farmers Branch homeowners call us because we write down the price before we touch a single tool. No one likes a number that grows between the diagnosis and the end of the job, and the Kingswell Way means that doesn’t happen here. Victor Mancini leads our Dallas operation, and he built the team around one habit: say what the work costs, do the work right, and put the guarantee on paper before the technician leaves.
Our technicians drive into Farmers Branch from the Dallas-Fort Worth office, so we’re not routing a truck from across the metroplex when your furnace quits on a 35-degree night. We work in the neighborhoods north of I-635, through Valwood, Brookhaven, and the original 1950s subdivisions that give this city its character. We know which streets have the tight utility closets and which houses have furnaces shoved into attics, because we’ve repaired systems in most of them.
Every repair is covered by the 365-Day Done Right Promise. If the fix fails inside a year, we come back and correct it at no charge. No fine print, no argument. We hand you the guarantee in writing, on the spot.
Styles & brands we work with
Furnace Maintenance in Farmers Branch
Furnace Maintenance in Farmers Branch is not a seasonal luxury. A tune-up here runs $80 – $200, and it’s the cheapest insurance a homeowner can buy against a mid-January breakdown, especially in slab-built ranch homes where a furnace sits in a closet that hasn’t been opened since the last cold snap. Our maintenance visit includes cleaning the burners and flame sensor, testing the gas valve, checking heat exchanger integrity with a combustion analyzer, and measuring static pressure to catch duct problems before they kill a blower motor.
What a Furnace Tune-Up Catches Before It Fails
A dirty flame sensor is the number one cause of a furnace that fires up and then shuts down two minutes later. We clean it, test it, and show you the reading. On two-stage and variable-speed systems, we calibrate the thermostat to match the equipment, because an old thermostat left in place after a new furnace install causes short-cycling that burns through parts and drives gas bills up.
Common Maintenance Findings in Farmers Branch Attic Furnaces
Furnaces installed in attics collect dust faster than closet units, and attic humidity corrodes electrical connections over time. We inspect the control board, tighten connections, and clear condensate drain lines with a wet-vac before the rust and scale cause a rollout switch lockout. The flat $80 – $200 covers the whole visit, with no add-on charges invented at the door.
Heat Pump Repair in Farmers Branch
Heat Pump Repair in Farmers Branch matters more than most homeowners realize, because many of the newer infill homes and apartment complexes in this city run heat pumps rather than separate furnaces and air conditioners. When a heat pump’s reversing valve sticks or the defrost board fails, the system blows cold air in winter and runs endlessly in summer. A typical heat pump repair here lands in the same $150 – $700 range as furnace work, depending on what failed.
Heat Pump Reversing Valve and Defrost Failures
A stuck reversing valve is the classic “my heat pump is blowing cold air in December” problem. The valve is a brass fitting that switches refrigerant flow between heating and cooling mode, and when it jams, the system thinks it’s still in summer. We test the valve with a magnet and replace it if needed, same visit. Defrost board failures are rarer but show up as ice coating the outdoor unit even on mild days, and those boards run on the lower end of the repair range.
Thermostat and Control Board Calibration for Heat Pumps
Many Farmers Branch heat pumps were installed with the original builder-grade thermostat, which doesn’t talk correctly to newer two-stage equipment. The result is short-cycling, uneven temperatures, and higher electric bills. We calibrate the thermostat and stage settings as part of any heat pump repair, because fixing the mechanical problem without fixing the control problem just means another call next month.
Trusted Brands We Service in Farmers Branch
Our technicians are trained on nine major HVAC brands, and in Farmers Branch we most often repair Trane, Goodman, and Rheem furnaces sitting in those 1960s and 1970s ranch homes. We keep common replacement parts in our trucks, including igniters, flame sensors, capacitors, gas valves, and blower motors, so most calls get fixed in one visit rather than waiting on a parts run. Furnace Repair on a brand-new builder unit is usually straightforward; repair on a 30-year-old system takes a technician who knows which parts are still available and which are discontinued. We’re on call for all of it in Farmers Branch.
See the difference
Before
After
Before
After
Before
AfterCommon Furnace Repair Problems We See in Farmers Branch Homes
- Rollout switch lockouts on older slab ranch furnaces. The rollout switch detects flame or heat where it shouldn’t be, and in tight utility closets, a clogged condensate line or a rusted heat exchanger trips it constantly. Homeowners reset it a few times, then it locks out for good.
- Frozen evaporator coils in summer-choked duct systems. Return air in these 1950s-1970s houses often flows through undersized flex duct added during a past remodel. When return air is restricted, the coil freezes on the hottest afternoons, and the furnace blower burns out fighting the blockage.
- Multi-zone dampers binding in large ranch homes. Zone dampers sit in the ductwork and open or close to direct heat. Years of Texas attic heat seize the metal pivots, one bedroom gets all the heat, and the furnace overheats trying to satisfy the thermostat.
- Condensate drain clogs in slab foundation houses. High-efficiency furnaces produce acidic condensate that runs through PVC lines routed through slab penetrations. In Farmers Branch, hard water mineral scale builds up in those lines and backs up water onto the closet floor.
Pricing for Furnace Repair in Farmers Branch, TX
Most furnace repairs in Farmers Branch fall between $150 and $700. The lower end covers capacitors, igniters, flame sensors, and simple gas valve adjustments. The upper end covers blower motor replacement, heat exchanger repair, and zone damper work. Here’s what you can expect, written down the same way we’d put it on your estimate:
| Repair Item | Price Range (Parts & Labor) |
|---|---|
| Furnace Repair (typical) | $150 – $700 |
| Capacitor replacement | $150 – $300 |
| Blower motor replacement | $350 – $700 |
Before any work starts, you get the written price. If we find something else while we’re in there, we stop and show you before we do anything. Estimates are free, and there’s no overtime charge on emergency calls. Call (430) 213-5796 for an exact quote on your system.
The one big local variable is the ductwork. A furnace repair inside the cabinet is predictable; a repair that involves reworking duct runs through a slab or a cramped attic closet takes more labor hours. We’ll tell you exactly what’s involved before you approve anything.
We Also Serve Cities Near Farmers Branch
Farmers Branch sits in the middle of the metroplex, and our trucks regularly cover Dallas, Arlington, Irving, and Carrollton. If you have family in a neighboring city whose furnace just quit, call us. Same team, same written guarantee, same live person on the phone.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Farmers Branch
The rollout switch is tripping because heat or flame is backing out of the burner chamber, almost always due to a clogged condensate drain, a rusted heat exchanger, or blocked exhaust flue pipes inside that cramped utility closet. A tripped rollout switch is not a “reset and forget” problem. Call (430) 213-5796, and our technician will test the heat exchanger and clear the drain before it becomes a carbon monoxide risk.
Yes, in most cases you can replace just the blower motor. A blower motor replacement on a Trane furnace in Farmers Branch runs $350 – $700, parts and labor included, and it’s a common repair on these 1970s ranch homes where the motor has been running against corroded ductwork for decades. If the heat exchanger is also cracked or the system is over 25 years old, we’ll show you the numbers and let you decide, but a motor alone is a straightforward fix we do same-day.
Your furnace is short-cycling if it fires up, runs for three to five minutes, then shuts off before the house reaches the set temperature. When this starts right after a new two-stage or variable-speed furnace was installed on a builder-grade thermostat, the thermostat was never calibrated for the new equipment. We check this first on every short-cycle call in Farmers Branch, because fixing the thermostat settings costs far less than replacing parts that aren’t actually broken.
Condensate leaks in slab-built Farmers Branch homes happen when the PVC drain line from a high-efficiency furnace clogs with mineral scale from North Texas hard water. The line runs through a tight slab penetration, scale builds up, water backs out onto the closet floor, and the rollout switch often trips as a secondary result. Our technicians clear the line with a wet-vac and flush it, and we can reroute the drain if the original install put it in a spot that keeps clogging.
Your furnace is blowing cold air because either the gas valve is failing to open, the igniter is cracked, or you have a heat pump and the reversing valve is stuck in cooling mode. In Farmers Branch, the heat pump scenario is common in newer infill homes, while the gas valve and igniter issues show up in the older ranches. We diagnose all three causes in the first 30 minutes of the visit. Call (430) 213-5796 for a same-day appointment, and we’ll put the written price in your hand before we start.
Written by Victor Mancini, Owner at Cold Harbour Heating and Air Dallas, serving Farmers Branch and the surrounding metroplex since 2003.