Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
TraneSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterFurnace Repair in Dallas, TX
Furnace repair in Dallas typically runs $150 to $650 for most common fixes, with simple part replacements like igniters or flame sensors on the lower end and blower motor or control board work on the higher end. Cold Harbour Heating and Air Dallas gets a written price in your hand before any work starts, and every repair carries our 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge. Call (430) 213-5796 and a live person answers, day or night.
Dallas winters swing hard. One week it’s 65 degrees, the next there’s ice on the grass and your furnace is struggling to hold 68 inside. When that happens, you need a repair company that picks up the phone, shows up in the window it promised, and puts the guarantee on paper before leaving. That’s how we operate. We’re part of the Kingswell network, which means our Heating & Furnace in Dallas work follows the same written standards every time: price before the work, a firm arrival window, a clean job site, and a guarantee that brings us back free if the repair doesn’t hold.
Victor Mancini has led our Dallas furnace repair team since 2003. Homeowners in Lakewood, Richardson, Garland, and Mesquite call us for the same reasons: they’ve been burned by a no-show, a price that jumped at the door, or a repair that quit within a month. We don’t operate that way, and we haven’t for over two decades.
When You Need Furnace Repair
Most furnace failures announce themselves before they become full-blown breakdowns. Here are the signs we see most often in Dallas homes between November and February:
- The furnace blows cold or lukewarm air. This usually points to a failed igniter or a tripped limit switch. In older Dallas homes with original ductwork, it can also signal a cracked heat exchanger, which needs immediate attention.
- Short cycling. The furnace starts, runs three to five minutes, shuts off, then repeats. Dirty flame sensors cause this constantly, especially in homes near White Rock Lake where dust and pollen levels run high.
- Unusual noises. A loud bang when the burners light means delayed ignition, a squeal suggests a failing blower motor bearing, and a rattle often means a loose panel or failing inducer motor. None of these fix themselves.
- Pilot light or igniter won’t stay lit. In older furnaces, a weak thermocouple. In newer systems, a failed hot surface igniter. Both are straightforward repairs when caught early.
- Higher gas bills with no change in usage. A furnace running inefficiently works harder and longer. In Dallas, where heating season is short but intense, a 30% spike in your January bill is often the first warning sign of a failing component.
- Yellow or flickering burner flame. A healthy gas furnace burns blue. Yellow flame indicates incomplete combustion, which can produce carbon monoxide. If you see this, turn the furnace off and call us at (430) 213-5796 right away.
Our Furnace Repair Process
Here’s exactly what happens when you call Cold Harbour Heating and Air Dallas for furnace repair:
- You talk to a person. No voicemail trees, no answering service script. A live person answers 24 hours a day, 7 days a week, and gets you scheduled for a firm arrival window.
- A background-checked, uniformed technician arrives. You know exactly who’s walking through your door. Our techs carry ID and wear Cold Harbour uniforms on every visit.
- We diagnose and write the price down. Before a single tool comes out of the bag, you get a written price for the repair. This is The Kingswell Way, and it doesn’t change at the door. No pressure, no surprises.
- You approve, we fix. Our technicians are trained to service nine major residential brands including Trane, Lennox, and Goodman, so whatever system is in your home, we can work on it.
- We test the system and clean the work area. We run the furnace through a full heating cycle, check venting, and leave the space cleaner than we found it.
- You get the repair in writing. Before we leave, you receive a written 365-Day Done Right Promise. If that repair fails within a full year, we return and correct it at no charge. No argument, no fine print.
Furnace Repair Pricing in Dallas
Furnace repair costs in Dallas vary by part, furnace age, and brand, but here’s what we actually see across the metro area. These ranges include parts and labor:
- Flame sensor cleaning or replacement: $120 – $200
- Igniter replacement: $150 – $280
- Thermocouple replacement: $140 – $230
- Pressure switch replacement: $160 – $290
- Capacitor replacement: $130 – $240
- Blower motor replacement: $380 – $650
- Inducer motor replacement: $350 – $600
- Control board replacement: $300 – $550
- Gas valve replacement: $280 – $500
- Heat exchanger replacement: $900 – $1,800 (and here we honestly recommend comparing against a new furnace)
What moves the price? Furnace age and brand matter. A Rheem unit from 2015 has easier-to-source parts than a discontinued model from the early 2000s. Accessibility matters too: Dallas homes with furnaces in tight attic spaces (common in older East Dallas bungalows) take longer to work on than units in open garages or utility closets. And the specific part matters most: a $15 flame sensor is a quick fix, while a blower motor involves more labor and a heavier component price.
Every quote is free. Call (430) 213-5796 and we’ll tell you the diagnostic fee upfront, then give you a written repair price before any work begins. If you decide not to proceed, you owe us nothing beyond the diagnostic visit.
FAQs – Furnace Repair
How much does furnace repair cost in Dallas?
Most furnace repairs in Dallas run between $150 and $650, with common fixes like igniter replacements at $150 – $280 and larger repairs like blower motors at $380 – $650. Your exact price depends on the part, your furnace brand, and how accessible the unit is. Call (430) 213-5796 for a free estimate on your specific system.
Can you repair my furnace the same day?
In most cases, yes. We keep common parts for Trane, Lennox, Goodman, and Rheem furnaces stocked on our trucks, which lets us complete the majority of repairs in a single visit. If your part is uncommon or your furnace is older, we’ll give you a clear timeline during the diagnostic call. Call (430) 213-5796 and a live person will get you scheduled.
Is it cheaper to repair or replace my furnace?
As a rule, if the repair costs less than 30% of a new furnace and your system is under 15 years old, repair makes more financial sense. If you’re looking at a cracked heat exchanger or repeated failures on a furnace over 15 years old, replacement is usually the smarter long-term decision. We’ll give you honest numbers for both options and let you decide.
Why is my furnace blowing cold air?
The most common causes are a dirty flame sensor, a failed igniter, or a tripped limit switch. In some cases it’s a gas supply issue or a failing control board. We diagnose the exact cause before quoting any work, and you get the written repair price before we proceed.
Do you charge extra for after-hours or weekend furnace repair?
No. Our pricing structure is the same regardless of the hour or day. A live person answers the phone 24/7, and the written price you receive is the written price you pay, whether it’s Tuesday at noon or Sunday at 2 a.m. Call (430) 213-5796 anytime.
What does your furnace repair guarantee cover?
Every repair we perform is covered by our 365-Day Done Right Promise. If the same repair fails at any point within one full year, Cold Harbour Heating and Air Dallas returns and corrects the work at no additional charge. The guarantee is written down and handed to you before our technician leaves.
Do you repair all furnace brands?
Our technicians are trained to service nine major residential HVAC brands, including Trane, Lennox, Goodman, Rheem, Carrier, Bryant, and American Standard. Whatever system is in your Dallas home, the technician who arrives can work on it.
Why Dallas Homeowners Call Cold Harbour
Dallas has no shortage of HVAC companies. What separates us is simple: we put the important things in writing. The Kingswell Way is built on five values that every Cold Harbour job follows: say the price before the work, show up in the window given, leave the place cleaner than found, put the guarantee in writing, and come back if it fails. That last one isn’t a policy we apply case by case. It’s on paper, every time.
The name Cold Harbour comes from the old roadside shelters where travelers waited out bad weather. Our job is to make sure your home is the place where the weather never gets in the way. A furnace that won’t start on a 30-degree Dallas morning is more than an inconvenience; it’s your family’s comfort and safety on the line. We treat it that way.
If your furnace is acting up, don’t wait for the next cold snap to make it worse. Call (430) 213-5796 now. A live person answers, you’ll get a firm arrival window, and the repair is covered in writing for 365 days. That’s how furnace repair in Dallas should work.
Written by Victor Mancini, Owner at Cold Harbour Heating and Air Dallas, serving Dallas.